110V 800w 24000RPM ER11 water cooling Woodworking AC Spindle motor 4 bearings

Description

1HP 0.8kw 24000RPM ER11 water cooling Woodworking AC Spindle motor 65mm 4 bearings 110VAC 10A 400hz CNC Router
1, Spindle Specification
Brand
HY
Spindle Model
65 800w 110v
Dimension
65mm*196mm
Speed
24000rpm
Rated Power
0.8kW
Voltage
AC110V
Current
5A
Frequency
400HZ
Bearings
2*7002, 2*7000
Collet
ER11
（
Random send a collet as free
）
Cooling Type
Water cooling
Lubricate
Grease
Plug connection:
Plug in 1234 pin, 1-U, 2-V, 3-W, 4-GND or not connected. if 123 not connected correctly, the motor will reverse. Swap any two wires can be OK.
2,
Instructions
1
The electric spindle must be matched with the frequency converter. Frequency converter selection must be matched with the power, voltage, current, frequency and other parameters of the electric spindle. The use of electric spindle must first set the benchmark frequency of the inverter. The reference frequency of the frequency converter is set according to the highest frequency of the electric spindle.
Inverter reference frequency conversion factory default settings 50hz. If the base frequency of the inverter is not set before the spindle motor is used, the spindle motor can be burnt down.
2
Before use, you should use the hand to turn the spindle motor, and confirm that it can rotate smoothly.
3
When in use, you must first connect to the spindle motor cooling water pipes, water pipes to ensure. Water flow is not less than 5L/min
4
If the electric spindle needs to be replaced with a new bearing,
Should be replaced by a certain professional and technical personnel. Supporting special tools. The spindle motor should be fully cleaned, the stator coil does not need to be removed.
3,
The common faults and their elimination methods
The Fault
The Reason
The Solution
The electric spindle does not run after start
1.No output or wrong setting for the inverter
check the output and setting of the inverter
2.Plug not connected
check the plug and connection cable
3.the cable not connected
4.The stator winding burned
change the stator
Few seconds after start,the spindle stop running
1.water inlet
Drying stator
2.High temperature induced wire insulation damage
change the stator
3.Lack of phase operation caused over current protection
check the cable connecting of the spindle motor
4.Start-up time is too short
Extended acceleration time
Motor smoke or shell hair hot
1.The inverter output voltage, frequency is not match with the spindle motor
check the setting of the inverter
2.the frequency of the inverter is not set correctly
reset the frequency of the inverter
3.Air duct blockage
check the air duct
Nut loosening when start
Rotation direction error
recorrect the rotation according the instruction on spindle
Noise and vibration
1,bearing damaged
change bearings
2.Parts precision damage affect dynamic balance
Check dynamic balance
3.Large spindle runout
change spindle
Nut loosening when stop
Down time is too short
Prolonged deceleration time
Payment
1. We accept PAYPAL.
2. If you have any difficulty in paying your items, pls contact us first and we will soon help to solve it.
Shipping
1. Rule all items will be shipping within 3-5 business days after you placed order.
2. UPS/DHL/FedEX express shipping usually takes 3-7 working days depended on the country delivered to. We will choose the best and most suitable shipping for you.
3. Customer should pay for the custom fee in any case.
4. We are not responsible for any accidents, delay or other issues that are the responsibility of the shipping service.
Warranty& Return Policy
1. The items are ALL BRAND NEW .All products have been checked and packaged in good condition before dispatch.
2. You have 14 days to return the items from the date they were received. If the items are your possession more then 14 days, we would provide the 12 months Manufacturer’s for defective items.
3. All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and your ID.
4. Return shipping is to be paid by the buyer.